GETTING FAMILIAR WITH PLUMBING: THE FIRST STEP FOR BATHTUB INSTALLATION

Getting Familiar with Plumbing: The First Step for Bathtub Installation

Getting Familiar with Plumbing: The First Step for Bathtub Installation

Blog Article

Book

We've stumbled on this great article pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround listed below on the web and concluded it made perfect sense to relate it with you in this article.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Installing a bathtub isn't precisely brain surgery, yet it does call for strong plumbing, carpentry, and also often, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the task can move rapidly; if you have to open a wall surface to remove the old bathtub and position the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will need a helper to vacate the old tub and set in the brand-new one. See to it you have actually qualified on your own for the task as well as are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed job, it is far better to think about employing one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This article will assist you mount a brand-new bath tub in your bathroom if you have currently gotten a brand-new tub and do not require to alter the plan of your previous water supply pipes.
Your devices and product list must consist of the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipeline Caps


  • Planning for the Setup


    To start with, the supporting structure provided with the bathroom should be fitted (if called for) according to the producer's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps system to avoid strain on the bath tub.
    Fit the versatile tap connectors to the bottom of both taps utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you utilize every one of the supplied washing machines.
    Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final position.

    Removing Old Touches


    If you need to replace old faucets with new ones as a part of your installment, then the first thing you must do is separate the water system. After doing so, activate the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be fairly problematic as a result of the limited gain access to that is typically the situation.
    Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will certainly originate from the pipes. When the supply pipes have actually been removed, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from turning throughout this process. When the taps have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
    Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.

    Setting up the Tub


    Using both wooden boards under its feet, put the bathtub in the called for position. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small points.
    The next goal is to make certain that the tub is leveled all round. This can be accomplished by examining the spirit level and adjusting the feet on the bath tub till the level checks out level.
    To set up taps, fit the bottom of the furthest flexible tap adapter to the appropriate supply pipe by making a compression join; then do the very same for the various other tap.
    Switch on the water system and check all joints as well as new pipework for leakages and tighten them if necessary. Fill the tub and additionally examine the overflow electrical outlet as well as the typical electrical outlet for leaks.
    Ultimately, take care of the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub must wait till the bathtub has actually been made use of at least once as this will settle it into its final position.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will require a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existing supply pipelines.
    If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
    Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former type ought to be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bath tub


    In the location where the bathroom satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with moisture and feasible leaks to the ceiling below.
    You can pick from a range of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to enable the motion experienced when the tub remains in use. The sealer can fracture fairly early if you do not think about this motion before sealing.
    Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant glue as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    I stumbled upon that article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a lookup on the internet. Are you aware of somebody else who is inquisitive about the niche? Please feel free to share it. We love reading our article about Tools You Need to Install a New Bathtub .


    Top plumbers, call!

    Report this page